Conformal coatings provide a long-term, stable and reliable encapsulation method for the electronic components from the environmental effects. Different industries and service conditions calls for different protective coatings. In some cases, changes in the requirements or mistakes would call for action to remove the coating. While some coating materials are easily removed, some are virtually impossible to remove without damaging the products (eg. epoxy) . The coating removal process has been standardized by the standard IPC-7711C/7721C titled Rework, Modification and Repair of Electronic Assemblies . According to the IPC-7711C/7721C coating removal starts by the identification of conformal coating (Chart. 1) type and followed by the selection of the method to be used depending on the substrate and components. If prepared onsite the coating material is generally known, but if the coating was done elsewhere the following chart can be used to identify the type of conformal coating.Read More
Parylene Coating Blog by Diamond-MT
Conformal coatings provide reliable working security for PCBs. However, poor coating application or selection of the wrong coating material can cause assembly malfunction. In other cases, poorly manufactured PCBS may need component repair/replacement. When these problems arise, coating removal is necessary.Read More
Failures of PCBs and similar electronic assemblies can occur despite the protection of conformal coating. Contributing reasons include:Read More
If problems in a conformal coating defy reliable repair, coating removal may be the only solution. Removing conformal coating from PCBs requires matching removal methodology with coating type and the component’s function. A variety of factors – bubbles/voids, coating thickness, component failure, inadequate masking, poor adhesion, surface finish, among many others – can necessitate coating removal.Read More
Conformal coatings protect printed circuit boards (PCBs) and similar electronic assemblies used for a wide range of aerospace, automotive, consumer, defense and medical applications. Coatings effectively cover PCBs, shielding them from contaminants, liquid incursions, temperature fluctuations and other conditions potentially hazardous to component performance. However, problems can develop if their preparation, application, and drying processes are inappropriately managed.Read More
It is possible to remove unwanted conformal coatings from PCBs in-shop. The process can often be accomplished by either the assembly’s original equipment manufacturer (OEM) or an end-user, but the capacity to do so doesn’t always exist. For these parties, conditions affecting the poor coating may:Read More
Sometimes problems with conformal coating are too complicated or difficult to repair. This can occur when bubbles develop in the coating during the application process; bubbles cause voids in the coating that defeat its protective, insulating purpose, suggesting the need for removal. Other situations that lead to inadequate coverage, and may favor coating removal, rather than repair include:
- Coating application that’s either too thick or thin for the project’s purposes.
- Component surface finishes that adapt poorly to the conformal material chosen for coverage.
- Disparities in surface tension/surface energy.
- Gravity issues that negatively impact application of liquid coating.
- Improper mixture of two-part materials.
- Inadequate fixturing or placement of assembly components in the coating area.
- Inadequate masking implementation.
- Incorrect interpretation of coating requirements.
- Residue on the coating surface during coating application.
- Poor, uneven coating application.
Overly thick film application or use of coating equipment/materials unsuited to the assignment are major causes of coating problems. In these cases, complete or partial removal of the conformal film from the PCB may be the best solution.
Thus, it is important before beginning any conformal coating assignment for designers and users to recognize the various types of conformal coatings and their interactions with the parts/materials they cover, to protect the products in their respective end-use environments, for the expected design-life of each component.
When removal is the best option for your coating problem, it is advisable to consult prevailing industry standards for appropriate process guidelines. For instance, IPC-7711/7721 delineates recommended procedures for conformal coating removal from, and replacement onto, PCBs. IPC-A-610 is a widely-held standard for electronic assemblies, offering users limited but valuable criteria for conformal coating applications. Designed and constructed with the intent of obtaining maximum confidence in the materials with minimum test redundancy, IPC-CC-830B qualifies the definition, use and conformance of all conformal coatings types for PCBs. In most cases, coating removal is required when assemblies don’t meet the requirements of IPC-CC-830, concerning overall quality conformance of each
The Logistics of Coating Removal
The logistics of coating removal are largely dependent on the type of coating material, its position on the PCB, and the board’s components. Proper identification of the coating material, and the methods used for its original application, are essential to correct determination of the removal method. Once these have been identified, determination of the appropriate removal method can be achieved.
In many cases, chemical strippers can dissolve conformal coatings from PCBs. Acrylic films are typically removed easily by soaking in a solution of stripping fluid, followed by mild mechanical abrasion if necessary. These two processes also work for coatings such as epoxy, silicone and urethane; however, since these substances have higher levels of chemical resistance than acrylic, complete coating removal is more difficult and time-consuming. In all cases, the stripping solution’s compatibility with the PCB’s components needs to be verified to minimize potential damage during the removal process.
Chemical removal does the least damage to PCBs; it is effective for the liquid coatings -- acrylic, epoxy, silicon and urethane. Chemical methods work less well for parylene films, since the substance is chemical inert. Abrasion, laser, mechanical, plasmatic and thermal removal methods are more successful for parylene films; they also work for liquid coatings in many cases.
Recently applied coating is more easily detached from substrate surfaces than older coatings, regardless of the material, unless the coating itself has begun to decay with age. Larger areas of the board respond best to complete submersion in a tank of stripping fluid. Gentle abrasion using a soft bristle brush will also eradicate coatings.
Please remember that the removal of conformal coating generally requires use of exceptionally caustic and potentially dangerous chemicals; the safety of process operators, the product being treated and the immediate environment can be jeopardized by use of inappropriate removal materials and methods. Consultation with a certified conformal coating specialist is highly recommended prior to removing conformal coating. To this end, the professionals at Diamond MT are eminently qualified, and would be glad to be of assistance.
To discover more about conformal coating rework and removal, download our whitepaper now:Read More
Defects to either the PCB assembly or its conformal coating can be sufficient to cause coating removal. Whether repair technologies address the circuit board’s components or the conformal film, subsequent post-repair coating (recoating) processes need to address:Read More
- Conformal coating applied incorrectly can cause PCB malfunction.
- Selecting the wrong coating material from among acrylic, epoxy, parylene, silicone or urethane can be a source of board failure, if it does not support the PCB’s operating environment.
Removing the coating may be necessary if these conditions prevail.Read More
Conformal coatings are designed to protect printed circuit boards (PCBs), assuring they work under all operational circumstances. However, cases emerge where boards fail to function despite conformal coating protection. Such non-performance can be a consequence of:Read More